Home/Prodotti/Sensori/Sensori di forza/Dinamometri Multicomponente, coppie massime fino a 200 Nm/9272

Dinamometro Multicomponente, Mz max ±200 Nm / 9272

Dinamometro Multicomponente, Mz max ±200 Nm
9272
18007552
  • Dinamometro multicomponente piezoelettrico con coppia massima ±200 Nm
  • Coppia massima Mz ±200 Nm
  • Frequenza naturale fn (x), fn (y) 3,1 kHz, fn (z) 6,3 kHz, fn (Mz) 4,2 kHz
  • Connettore flangiato Fischer a 9 pin
Su richiesta
Su richiesta
Accedi a myKistler per visualizzare i prezzi
Measuring ranges
Minimum measuring range [kN]
-5 kN
Maximum measuring range [kN]
20 kN
Product type
Force sensor type
A dynamometer is a force plate measuring forces and moments.
Multicomponent dynamometer
Preloaded sensor
Preloaded sensors are already calibrated and therefore ready-to-use. Non-preloaded sensors are smaller.
Yes
Mechanical properties
Stiffness Cx [kN/μm]
0.4 kN/μm
Stiffness Cy [kN/μm]
0.4 kN/μm
Stiffness Cz [kN/μm]
2 kN/μm
Stiffness Cφ (Mz) [kN/μm]
0.7 N·m/μrad
Overload Fx [kN]
-6, 6 kN
Overload Fy [kN]
-6, 6 kN
Overload Fz [kN]
-6, 24 kN
Overload Mz [N·m]
-240, 240 N·m
Maximum bending moment Mxy (single load)
400 N·m
Crosstalk
Maximum crosstalk Fx→Fy
-2 … 2 %
Maximum crosstalk Fy→Fx
-2 … 2 %
Maximum crosstalk Fz→Fx
-1 … 1 %
Maximum crosstalk Fz→Fy
-1 … 1 %
Maximum crosstalk Mz→Fx
-0.5 … 0.5 N/N·m
Maximum crosstalk Mz→Fy
-0.5 … 0.5 N/N·m
Maximum crosstalk Mz→Fz
-1 … 1 N/N·m
Metrological characteristics
Linearity
Linearity represents the maximum deviation/error between ideal and actual output signal characteristics in relation to the measurand in a specific measuring range. It is expressed in percentage of the range of measurement signal (Full Scale Output).
≤±1 %FSO
Hysteresis
≤1 %FSO
Nominal sensitivity Mz [pC/N·m]
-160 pC/N·m
Threshold Fx
Minimum change in the measurand that produces a measurable change in the sensor output, while the change of the measurand takes place slowly and monotonically.
0.01 N
Threshold Fy
Minimum change in the measurand that produces a measurable change in the sensor output, while the change of the measurand takes place slowly and monotonically.
0.01 N
Threshold Fz
Minimum change in the measurand that produces a measurable change in the sensor output, while the change of the measurand takes place slowly and monotonically.
0.02 N
Threshold Mz
Minimum change in the measurand that produces a measurable change in the sensor output, while the change of the measurand takes place slowly and monotonically.
0.2 mN·m
Electrical properties
Output signal type
Charge (Piezoelectric, PE)
Capacitance
185 pF
Minimal insulation resistance
10^13 Ω
Ground Insulation
>10^8 Ω
Influence quantities
Sensitivity
Fx: -7.8 pC/N, Fy: -7.8 pC/N, Fz: -3.5 pC/N, Mz: -160 pC/N
Temperature coefficient of sensitivity
–0.02 %/°C
Certificates and Standards
Degree of protection EN 60529
IP67
Operation and installation
Operating temperature range
0 … 70 °C
Applications
Cutting processes and machining development
Cable properties
Cable included
No cable included
Interfaces
Connector type
Fischer 104 9-pole neg.
Dimensions and materials
Weight
4.2 kg
Si tratta di un dinamometro a quattro componenti per la misurazione di una coppia Mz e delle tre componenti ortogonali di una forza. Il dinamometro ha una grande rigidità e di conseguenza un'elevata frequenza naturale. La sua elevata risoluzione consente di misurare le più piccole variazioni dinamiche di forze e coppie di grandi dimensioni.
Caricamento in corso
Caricamento in corso