Triaxial load cell, piezoelectric force transducer Fx, Fy, Fz (Fz ±8 kN / ±1.79 klbf) / 9327C

Preloaded 3-component force sensors from Kistler are a good choice for tire end-of-line (EOL) testing.
9327C
18007671
  • Triaxial piezoelectric load cell with measuring ranges Fx, Fy: -4 ... 4 kN and Fz: -8 ... 8 kN (±899 lbf / ±1.79 klbf)
  • Preloaded, calibrated and ready to measure
  • Nominal sensitivity Fz: -3.8 pC/N
  • Connection: V3 neg.
On request
On request
Maximum measuring range8 kNMeasuring range Fy [kN]-4 … 4 kNForce sensor typeTriaxial force sensorAxial stiffness1.379 kN/μmShear stiffness0.391 kN/μmLateral stiffness0.073 kN/μmPermissible moment loading Mz-22 … 22 N·mLinearity (force)≤±0.5 %FSOCalibrated range Fy [kN]0 … 1 kNThreshold≤0.01 NCapacitance30 pFGround Insulation>10^8 ΩOperating temperature range-40 … 120 °CConnector typeV3 (negative)ApplicationsNVH testing, eVTOL / UAV / drone testing, Space payload testing
Measuring range Fx [kN]-4 … 4 kNMeasuring range-8 … 8 kNPreloaded sensorYesBending stiffness0.625 kN·m/°Torsional stiffness0.682 kN·m/°Permissible moment loading Mx, My-23 … 23 N·mCalibrated range Fx [kN]0 … 1 kNLinearity≤±0.5 %FSOCalibrated range Fz [kN]0 … 8 kNOutput signal typeCharge (Piezoelectric, PE)Minimal insulation resistance10^13 ΩNatural frequency fn Fx3.2 kHzDegree of protection EN 60529IP68Weight0.380 kg
This triaxial load cell is a piezoelectric force transducer for the exact measurement of all forces on the three orthogonal components acting in an arbitrary direction. Independent of the point of force application, the load cells with the installed triaxial force transducers of the 90x7 family measure all three components of the applied force in highest resolution. The three axis load cells in the 93x7 product family are optimally preloaded, calibrated and immediately ready to measure. The triaxial load cells are mounted under preload between two plates and measure both tensile and compression forces in all directions. Based on the piezoelectric principle, a force produces a proportional electric charge. This is conducted via an electrode to the appropriate connector. The simple and vibration-resistant design of the force transducers is very rigid resulting in a high natural frequency, which is a requirement for highly dynamic force measurements. The 3-pole connector V3 neg. (design protected) is provided with a positioning aid. This guarantees accurate assignment and centering of the connector pins and sockets before connection. The plug connection is protected against rotation. After correct installation, the load cell is ready for use without recalibration. Triaxial force transducers allow simple, direct and very precise measurements.
Advertisements
English
pdf
For access, please click here to log in. You will be redirected automatically.
Data sheet
English
pdf
For access, please click here to log in. You will be redirected automatically.
Handout
English
pdf
For access, please click here to log in. You will be redirected automatically.
Manual
Triaxial load cell
English
pdf
For access, please click here to log in. You will be redirected automatically.
38 results
Accessory Type
Connecting cables (TPC black) for triaxial force sensors with V3 neg. connector
1698-3TPC
1698AN4sp
Price On request Availability
On request
Connecting cable for triaxial force sensors, V3 90°, 3 x KIAG 10-32 pos., exit angle 270°, down
1698AN3sp
Price On request Availability
On request
Connecting cable for triaxial force sensors, V3 90°, 3 x KIAG 10-32 pos., exit angle 180°, left