Rotating cutting force dynamometer (RCD), Fz max ±20 kN, Mz max ±150 Nm / 9170A

Rotating cutting force dynamometer (RCD), Fz max ±20 kN, Mz max ±150 Nm
9170A
18019313
  • Rotating multicomponent dynamometer with maximum forces Fx, Fy ±5 kN, Fz ±20 kN
  • Maximum torque Mz ±150 Nm
  • Speed: max. 20000 min-1
  • Telemetric data transmission
On request
On request
Log in to myKistler to see prices
Measuring ranges
Minimum measuring range [kN]
1 kN
Maximum measuring range [kN]
20 kN
Measuring range 1, nominal Fx, Fy
-5000 … 5000 N
Measuring range 1, nominal Fz
-20000 … 20000 N
Measuring range 1, nominal Mz
-150 … 150 N·m
Measuring range 2, nominal Fx, Fy
-2000 … 2000 N
Measuring range 2, nominal Fz
-5000 … 5000 N
Measuring range 2, nominal Mz
-50 … 50 N·m
Measuring range 3, nominal Fx, Fy
-500 … 500 N
Sensitivity range 1, Fx, Fy, approximate
2 mV/N
Measuring range 3, nominal Fz
-2000 … 2000 N
Measuring range 3, nominal Mz
-10 … 10 N·m
Product type
Force sensor type
A dynamometer is a force plate measuring forces and moments.
Multicomponent dynamometer
Preloaded sensor
Preloaded sensors are already calibrated and therefore ready-to-use. Non-preloaded sensors are smaller.
Yes
Mechanical properties
Internal cutting fluid pressure, maximal
70 bar
Crosstalk
Maximum crosstalk Fx→Fy
-2 … 2 %
Maximum crosstalk Fx→Fz
-3.5 … 3.5 %
Maximum crosstalk Fy→Fx
-2 … 2 %
Maximum crosstalk Fy→Fz
-3.5 … 3.5 %
Maximum crosstalk Fz→Fx
-1 … 1 %
Maximum crosstalk Fz→Fy
-1 … 1 %
Maximum crosstalk Fz→Mz
-1 … 1 N·m/N
Maximum crosstalk Mz→Fy
-1 … 1 N/N·m
Electrical properties
Output signal type
Charge (Piezoelectric, PE)
Influence quantities
Sensitivity range 1, Fz, approximate
0.5 mV/N
Sensitivity range 1, Mz, approximate
66 mV/N·m
Sensitivity range 2, Fx, Fy, approximate
5 mV/N
Sensitivity range 2, Fz, approximate
2 mV/N
Sensitivity range 2, Mz, approximate
200 mV/N·m
Sensitivity range 3, Fx, Fy, approximate
20 mV/N
Sensitivity range 3, Fz, approximate
5 mV/N
Sensitivity range 3, Mz, approximate
1000 mV/N·m
Certificates and Standards
Degree of protection EN 60529
IP67
Operation and installation
Operating temperature range
0 … 60 °C
Speed, maximal
20000 1/min
Applications
Cutting processes and machining development
Cable properties
Cable included
No cable included
Interfaces
Connector type
M16 6 pin circular connector
Dimensions and materials
Weight
1.6 kg
Signal filter and time constants
Low-pass Filter (anti-aliasing)
3 kHz
Additional properties
Balancing class
≤2.5 G
This is a rotating four-component dynamometer for measuring the forces and torque on a rotating tool during cutting processes. Energy and measured values are transmitted on a non-contact basis, preventing wear.
Data sheet
English
pdf
Please click here to log in to myKistler and you will be redirected.
Manual
Rotating Cutting Force Dynamometer (RCD)
English
pdf
Please click here to log in to myKistler and you will be redirected.
0 results
Accessory Type