Piezoelectric Press Force load cell, lightweight miniature force transducer, Fz max 0 … 5 kN / 9313AA1
- Preloaded and calibrated force transducer, ready to measure immediately
- Calibrated ranges Fz: 0 … 0,05 kN, 0 … 0,5 kN, 0 … 5 kN
- Sensitivity: ≈ –10 pC/N
- Dimensions DxH: 13x10 mm
Preloaded sensorYesMeasuring range0 … 5 kNMaximum measuring range5 kNForce sensor typeSingle axis force sensorCalibrated measuring range0 … 5 kN (Fz 100%)Rigidity Cz≈0.560 kN/μmMaximum measuring range Fz0 … 5 kNMaximum Overload tension/pressure–0.5 / 5.5 kNMaximum shear force Fx,y that equals lateral force at the joint0.1 kNMaximum tightening torque Mz0.3 NmMaximum bending moment Mx,y at Fz = 0%1.3 NmMaximum bending moment Mx,y at Fz = 100%0.2 NmCrosstalk Fx,y -> Fz<0.29 N/NCrosstalk Mx,y -> Fz<72 N/NCase materialDIN 1.4542Connector, electricalKIAG 10-32 neg.Temperature coefficient of sensitivity0.05 %/°CSensitivity–10 pC/NThreshold0.01 NOperating temperature range-40 … 120 °CLinearity≤±0.5 %FSOOutput signal typeCharge (Piezoelectric, PE)Degree of protection EN 60529IP67 (with welded sensor), IP65 (with connected cable)Weight (without cable)10 g
This lightweight miniature compression force sensor is particularly suitable for measuring dynamic forces and also quasistatic forces. Preloaded and provided with practical adaptation options, the sensor is ready for immediate use. The Press Force load cell is based on the piezoelectric measuring principle. The force acting on the crystal element produces a proportional electric charge at the signal output. A measuring amplifier connected downstream to the sensor converts this charge into a process signal which can be evaluated. The particularly square shape of the sensor body and the force introduction at both ends via axial threaded bores bring advantages in special mounting situations. Tensile forces up to 10 % of the compression force range are measured. These ranges are not calibrated. However, they are often used for the detection of tool withdrawal forces, for example after press fitting processes.
Press Force Sensor
Capteur de force de compression
Press Force Sensor
High-insulating connecting cables, KIAG 10-32 pos. - TNC pos., PFA green
Connecting cables for piezoelectric sensors, highly flexible, KIAG 10-32 pos. or M4x0.35 pos. - KIAG 10-32 pos. or BNC pos.
Connecting cables for piezoelectric sensors, very sturdy, KIAG 10-32 pos. - KIAG 10-32 pos. or BNC pos.
Laboratory charge amplifiers, multi-channel, low noise, measuring ranges ±2 to ±2200000 pC, freq. range ≈0 … 200 kHz
Connecting cables for piezoelectric sensors, KIAG 10-32 pos. - KIAG 10-32 pos.
Connecting cables for piezoelectric sensors, KIAG 10-32 pos. int. - BNC pos.
Industrial charge amplifiers for manufacturing applications (ICAM), 1 to 4 channels (±10 V / 4 … 20 mA)
Connecting cables for piezoelectric sensors, KIAG 10-32 pos. 90° - BNC pos.
Connecting cables for piezoelectric sensors, KIAG 10-32 pos. int. - TNC pos.
Laboratory charge amplifiers, 1-channel, low noise, measuring ranges ±2 to ±2200000 pC, freq. range ≈0 … 200 kHz