Accueil/Produits/Capteurs/Capteurs de force/Dynamomètres multicomposants, forces maximales jusqu'à 10 kN, plaque supérieure 100x170 mm/9257B

Dynamomètre multicomposant, 5 kN, plaque supérieure 100x170 mm / 9257B

Dynamomètre multicomposant, 5 kN, plaque supérieure 100x170 mm
9257B
18007542
  • Dynamomètre piézoélectrique à plusieurs composants avec forces maximales Fx, Fy, Fz ±5 kN
  • Plaque supérieure 100x170 mm
  • Fréquence propre fn (x), fn (y), fn (z) 3,5 kHz
  • Connecteur à bride Fischer à 9 broches
Sur demande
Sur demande
Measuring ranges
Minimum measuring range [kN]
-5 kN
Maximum measuring range [kN]
10 kN
Product type
Force sensor type
A dynamometer is a force plate measuring forces and moments.
Multicomponent dynamometer
Preloaded sensor
Preloaded sensors are already calibrated and therefore ready-to-use. Non-preloaded sensors are smaller.
Yes
Mechanical properties
Stiffness Cx [kN/μm]
1 kN/μm
Stiffness Cy [kN/μm]
1 kN/μm
Stiffness Cz [kN/μm]
2 kN/μm
Overload Fx [kN]
-7.5, 7.5 kN
Overload Fy [kN]
-7.5, 7.5 kN
Overload Fz [kN]
-7.5, 15 kN
Metrological characteristics
Linearity
Linearity represents the maximum deviation/error between ideal and actual output signal characteristics in relation to the measurand in a specific measuring range. It is expressed in percentage of the range of measurement signal (Full Scale Output).
≤±1 %FSO
Hysteresis
≤0.5 %FSO
Threshold
<0.01 N
Electrical properties
Output signal type
Charge (Piezoelectric, PE)
Capacitance
≈220 pF
Minimal insulation resistance
10^13 Ω
Ground Insulation
>10^8 Ω
Influence quantities
Sensitivity
Fx: -7.5 pC/N, Fy: -7.5 pC/N, Fz: -3.7 pC/N
Dynamical properties
Natural frequency Fx
Frequency of free (not forced) oscillations of the entire sensor. In practice the (usually lower) natural frequency of the entire mounted system governs the frequency behavior.
3.5 kHz
Natural frequency Fy
Frequency of free (not forced) oscillations of the entire sensor. In practice the (usually lower) natural frequency of the entire mounted system governs the frequency behavior.
3.5 kHz
Natural frequency Fz
Frequency of free (not forced) oscillations of the entire sensor. In practice the (usually lower) natural frequency of the entire mounted system governs the frequency behavior.
3.5 kHz
Certificates and Standards
Degree of protection EN 60529
IP67
Operation and installation
Operating temperature range
0 … 70 °C
Clamping area
100 mm x 170 mm
Cable properties
Cable included
No cable included
Interfaces
Connector type
Fischer 104 9-pole neg.
Dimensions and materials
Weight
7.3 kg
Il s'agit d'un dynamomètre piézoélectrique à trois composantes permettant de mesurer les trois composantes orthogonales d'une force. Le dynamomètre présente une grande rigidité et, par conséquent, une fréquence propre élevée. Sa haute résolution permet de mesurer les plus petites variations dynamiques de forces importantes.
Chargement
Chargement