Piezoelectric Press Force load cell, lightweight miniature force transducer, Fz max 0 … 5 kN / 9313AA1

9313AA1
9313AA1
18007649
  • Preloaded and calibrated force transducer, ready to measure immediately
  • Calibrated ranges Fz: 0 … 0,05 kN, 0 … 0,5 kN, 0 … 5 kN
  • Sensitivity: ≈ –10 pC/N
  • Dimensions DxH: 13x10 mm
 
 
Preloaded sensorYesMeasuring range0 … 5 kNMaximum measuring range5 kNForce sensor typeStandard force sensorCalibrated measuring range0 … 5 kN (Fz 100%)Rigidity Cz≈0.560 kN/μmMaximum measuring range Fz0 … 5 kNMaximum Overload tension/pressure–0.5 / 5.5 kNMaximum shear force Fx,y that equals lateral force at the joint0.1 kNMaximum tightening torque Mz0.3 NmMaximum bending moment Mx,y at Fz = 0%1.3 NmMaximum bending moment Mx,y at Fz = 100%0.2 NmCrosstalk Fx,y -> Fz<0.29 N/NCrosstalk Mx,y -> Fz<72 N/NCase materialDIN 1.4542Connector, electricalKIAG 10-32 neg.Temperature coefficient of sensitivity0.05 %/°CSensitivity–10 pC/NThreshold0.01 NOperating temperature range-40 … 120 °CLinearity≤±0.5 %FSOOutput signal typeCharge (Piezoelectric, PE)Degree of protection EN 60529IP67 (with welded sensor), IP65 (with connected cable)Weight (without cable)10 g
This lightweight miniature compression force sensor is particularly suitable for measuring dynamic forces and also quasistatic forces. Preloaded and provided with practical adaptation options, the sensor is ready for immediate use. The Press Force load cell is based on the piezoelectric measuring principle. The force acting on the crystal element produces a proportional electric charge at the signal output. A measuring amplifier connected downstream to the sensor converts this charge into a process signal which can be evaluated. The particularly square shape of the sensor body and the force introduction at both ends via axial threaded bores bring advantages in special mounting situations. Tensile forces up to 10 % of the compression force range are measured. These ranges are not calibrated. However, they are often used for the detection of tool withdrawal forces, for example after press fitting processes.
Data sheet
English
pdf
 
Chinese
pdf
 
Japanese
pdf
 
French
pdf
 
German
pdf
 
Manual
Press Force Sensor
German
pdf
 
Capteur de force de compression
French
pdf
 
Press Force Sensor
English
pdf
 
 
 
undefined
High-insulating connecting cables, KIAG 10-32 pos. - TNC pos., PFA green
1633C
1633CSP      
 
High-insulating connecting cable, KIAG 10-32 pos. - TNC pos., PFA green, customer-specific length
undefined
Connecting cables for piezoelectric sensors, very sturdy, KIAG 10-32 pos. - KIAG 10-32 pos. or BNC pos.
1900A21
1900A21A12SP      
 
Connecting cable for piezoelectric sensors, very sturdy, KIAG 10-32 pos. - BNC pos., custom, 0.3 to 20 m
1900A21A11SP      
 
Connecting cable for piezoelectric sensors, very sturdy, KIAG 10-32 pos. - KIAG 10-32 pos., custom, 0.3 to 20 m
undefined
Laboratory charge amplifiers, multi-channel, low noise, measuring ranges ±2 to ±2200000 pC, freq. range ≈0 … 200 kHz
5080A
5080A      
 
Laboratory charge amplifier, multi-channel, low noise, measuring ranges from ±2 to ±2200000 pC
undefined
Connecting cables for piezoelectric sensors, KIAG 10-32 pos. - KIAG 10-32 pos.
1635C
1635CSP      
 
Connecting cable for piezoelectric sensors, KIAG 10-32 pos. - KIAG 10-32 pos., custom length, 0.1 to 50 m
undefined
Connecting cables for piezoelectric sensors, KIAG 10-32 pos. int. - BNC pos.
1939A
1939ASP      
 
Connecting cable for piezoelectric sensors, KIAG 10-32 pos. int. - BNC pos., custom length 0.1 to 20 m
undefined
Connecting cables for piezoelectric sensors, KIAG 10-32 pos. int. - TNC pos.
1941A
1941ASP      
 
Connecting cable for piezoelectric sensors, KIAG 10-32 pos. int. - TNC pos., custom length, 0.1 to 50 m