Piezoelectric Press Force load cell, lightweight miniature force transducer, Fz max 0 … 5 kN / 9313AA1

9313AA1
18007649
- Preloaded and calibrated force transducer, ready to measure immediately
- Calibrated ranges Fz: 0 … 0,05 kN, 0 … 0,5 kN, 0 … 5 kN
- Sensitivity: ≈ –10 pC/N
- Dimensions DxH: 13x10 mm
On request
On request
Maximum measuring range5 kNSensitivity–10 pC/NPreloaded sensorYesMaximum Overload tension/pressure–0.5 / 5.5 kNMaximum bending moment Mxy (single load)1.3 N·mLinearity≤±0.5 %FSOThreshold0.01 NTemperature coefficient of sensitivity0.05 %/°CDegree of protection EN 60529IP67 (with welded sensor), IP65 (with connected cable)Weight (without cable)10 g
Measuring range0 … 5 kNForce sensor typeSingle axis force sensorStiffness Cz [kN/μm]0.56 kN/μmMaximum tightening torque Mz0.3 N·mShear force0.1 kNCalibrated range Fz [kN]0 … 5 kNOutput signal typeCharge (Piezoelectric, PE)Operating temperature range-40 … 120 °CConnector type10-32 UNF (negative)Casing materialDIN 1.4542
This lightweight miniature compression force sensor is particularly suitable for measuring dynamic forces and also quasistatic forces. Preloaded and provided with practical adaptation options, the sensor is ready for immediate use. The Press Force load cell is based on the piezoelectric measuring principle. The force acting on the crystal element produces a proportional electric charge at the signal output. A measuring amplifier connected downstream to the sensor converts this charge into a process signal which can be evaluated. The particularly square shape of the sensor body and the force introduction at both ends via axial threaded bores bring advantages in special mounting situations. Tensile forces up to 10 % of the compression force range are measured. These ranges are not calibrated. However, they are often used for the detection of tool withdrawal forces, for example after press fitting processes.
Data sheet
English
pdf
For access, please click here to log in. You will be redirected automatically.
Manual
Press Force Sensor
English
pdf
For access, please click here to log in. You will be redirected automatically.
126 results
Accessory Type

High-insulating connecting cables, KIAG 10-32 pos. - TNC pos., PFA green
1633C
1633CSP
Price On request Availability
On request
High-insulating connecting cable, KIAG 10-32 pos. - TNC pos., PFA green, customer-specific length

Connecting cables for piezoelectric sensors, very sturdy, KIAG 10-32 pos. - KIAG 10-32 pos. or BNC pos.
1900A21
1900A21A12SP
Price On request Availability
On request
Connecting cable for piezoelectric sensors, very sturdy, KIAG 10-32 pos. - BNC pos., length 0.3 to 20 m
1900A21A11SP
Price On request Availability
On request
Connecting cable for piezoelectric sensors, very sturdy, KIAG 10-32 pos. - KIAG 10-32 pos., length 0.3 to 20 m

Laboratory charge amplifiers, multi-channel, low noise, measuring ranges ±2 to ±2200000 pC, freq. range ≈0 … 200 kHz
5080A
5080A
Price On request Availability
On request
Laboratory charge amplifier, multi-channel, low noise, measuring ranges from ±2 to ±2200000 pC

Connecting cables for piezoelectric sensors, KIAG 10-32 pos. - KIAG 10-32 pos.
1635C
1635CSP
Price On request Availability
On request
Connecting cable for piezoelectric sensors, KIAG 10-32 pos. - KIAG 10-32 pos., length 0.1 to 50 m

Connecting cables for piezoelectric sensors, KIAG 10-32 pos. int. - BNC pos.
1939A
1939ASP
Price On request Availability
On request
Connecting cable for piezoelectric sensors, KIAG 10-32 pos. int. - BNC pos., length 0.1 to 20 m

Connecting cables for piezoelectric sensors, KIAG 10-32 pos. 90° - BNC pos.
1641B
1641BSP
Price On request Availability
On request
Connecting cable for piezoelectric sensors, KIAG 10-32 pos. 90° - BNC pos., length 0.1 to 50 m

Connecting cables for piezoelectric sensors, KIAG 10-32 pos. int. - TNC pos.
1941A
1941ASP
Price On request Availability
On request
Connecting cable for piezoelectric sensors, KIAG 10-32 pos. int. - TNC pos., length 0.1 to 50 m
For access, please click here to log in. You will be redirected automatically.