2-axis force and reaction torque transducer, Fz max ±20 kN, Mz max ±200 Nm / 9365B

9365B
9365B
18007718
  • Preloaded and calibrated force-torque sensor, ready to measure immediately
  • Calibrated ranges: Fz: 0 … +2 kN, 0 … +20 kN; Mz: 0 … ±20 N·m, 0 … ±200 N·m
  • Sensitivity: Fz: ≈ –3,6 pC/N, Mz: ≈ –140 pC/Nm
  • Dimensions DxH: 54x60 mm
 
 
Preloaded sensorYesMeasuring range-20 … 20 kNMaximum measuring range20 kNForce sensor typeMulticomponent Force / MomentCalibrated measuring range0 … 20 kN (Fz 100%)Measuring range Mz-200 … 200 NmOverload Mz±210 NmSensitivity Mz≈–140 pC/NmThreshold Mz<0.62 mNmCrosstalk Fz -> Mz≤±0.08 mNm/NCrosstalk Mz -> Fz≤±1 N/NmOverload Fz±24 kNThreshold Fz<0.35 NTemperature coefficient of sensitivity Fz–0.02 %/°CCrosstalk Fx,y -> Fz≤±0.02 N/NRigidity Cz (Fz)≈2.8 kN/μmCase materialDIN 1.4542Crosstalk Fx,y -> Mz≤±0.3 mNm/NCrosstalk Mb -> Fz≤±0.5 N/NmCrosstalk Mb -> Mz≤±0.01 Nm/NmHysteresis Fz≤0.5 %FSOHysteresis Mz≤0.5 %FSOLinearity Fz≤±0.3 %FSOLinearity Mz≤±0.3 %FSONatural frequency fn(Mz)>25 kHzNatural frequency fn(z)>33 kHzRigidity Cφ(Mz)≈0.92 Nm/μradCapacitance CFz≈150 pFCapacitance CMz≈350 pFTightening torque MA (recommended)21 NmSensitivity≈–3.6 pC/N (Fz), ≈–140 pC/Nm (Mz)Operating temperature range-40 … 120 °COutput signal typeCharge (Piezoelectric, PE)Degree of protection EN 60529IP65Insulation resistance at 20 °C>10^13 ΩWeight834 g
This piezoelectric 2-axis force-torque transducer is suitable for measuring a tensile or compression force Fz and a torque Mz acting on the sensor. The high resolution allows measurement of the slightest dynamic changes in large forces and torques at non-rotating shafts. Pressure and shear sensitive quartz disks are integrated under high preload between a hollow preload screw and a nut de signed as the sensor case. Because of the extremely high rigidity of the sensor elements, the components Fz and Mz are measured practically without change of stroke or angle. The force and torque-proportional charge signal is picked up by electrodes and fed via a shielded cable to the charge amplifier. The latter converts the charge signals into proportional output voltages, which can be recorded and evaluated.
 
 
undefined
Connecting cables (TPC black) for triaxial force sensors with V3 neg. connector
1698-3TPC
1698AN4sp      
 
Connecting cable for triaxial force sensors, V3 90°, 3 x KIAG 10-32 pos., exit angle 270°, down
1698AN3sp      
 
Connecting cable for triaxial force sensors, V3 90°, 3 x KIAG 10-32 pos., exit angle 180°, left
undefined
Laboratory charge amplifiers, multi-channel, low noise, measuring ranges ±2 to ±2200000 pC, freq. range ≈0 … 200 kHz
5080A
5080A      
 
Laboratory charge amplifier, multi-channel, low noise, measuring ranges from ±2 to ±2200000 pC