2-axis force and reaction torque transducer, Fz max ±10 kN, Mz max ±25 Nm / 9345B

  • Preloaded and calibrated force-torque sensor, ready to measure immediately
  • Calibrated ranges: Fz: 0 … +1 kN, 0 … +10 kN; Mz: 0 … ±2.5 Nm, 0 … ±25 Nm
  • Sensitivity: Fz: ≈ –3,7 pC/N, Mz: ≈ –190 pC/Nm
  • Dimensions DxH: 36x42 mm
Preloaded sensorYesMeasuring range-10 … 10 kNMaximum measuring range10 kNForce sensor typeMulticomponent Force / MomentCalibrated measuring range0 … ±2.5 Nm (Mz 10 percent)Measuring range Mz-25 … 25 NmOverload Mz±30 NmSensitivity Mz≈–190 pC/NmThreshold Mz<0.02 mNmCrosstalk Fz -> Mz≤±0.04 mNm/NCrosstalk Mz -> Fz≤±2 N/NmMeasuring range Fz-10 … 10 kNOverload Fz±12 kNThreshold Fz<0.02 NTemperature coefficient of sensitivity Fz–0.02 %/°CCrosstalk Fx,y -> Fz≤±0.02 N/NRigidity Cz (Fz)≈1.7 kN/μmCase materialDIN 1.4542Crosstalk Fx,y -> Mz≤±0.3 mNm/NCrosstalk Mb -> Fz≤±0.5 N/NmCrosstalk Mb -> Mz≤±0.02 Nm/NmHysteresis Fz≤0.5 %FSOHysteresis Mz≤0.5 %FSOLinearity Fz≤±0.3 %FSOLinearity Mz≤±0.3 %FSONatural frequency fn(Mz)>32 kHzNatural frequency fn(z)>41 kHzRigidity Cφ(Mz)≈0.19 Nm/μradCapacitance CFz≈65 pFCapacitance CMz≈340 pFTightening torque MA (recommended)4 NmSensitivity≈–3.7 pC/N (Fz), ≈–190 pC/Nm (Mz)Operating temperature range-40 … 120 °COutput signal typeCharge (Piezoelectric, PE)Degree of protection EN 60529IP65Insulation resistance at 20 °C>10^13 ΩWeight267 g
This piezoelectric 2-axis force-torque transducer is suitable for measuring a tensile or compression force Fz and a torque Mz acting on the sensor. The high resolution allows measurement of the slightest dynamic changes in large forces and torques at non-rotating shafts. Pressure and shear sensitive quartz disks are integrated under high preload between a hollow preload screw and a nut de signed as the sensor case. Because of the extremely high rigidity of the sensor elements, the components Fz and Mz are measured practically without change of stroke or angle. The force and torque-proportional charge signal is picked up by electrodes and fed via a shielded cable to the charge amplifier. The latter converts the charge signals into proportional output voltages, which can be recorded and evaluated.
Connecting cables (TPC black) for triaxial force sensors with V3 neg. connector
Connecting cable for triaxial force sensors, V3 90°, 3 x KIAG 10-32 pos., exit angle 270°, down
Connecting cable for triaxial force sensors, V3 90°, 3 x KIAG 10-32 pos., exit angle 180°, left
Laboratory charge amplifiers, multi-channel, low noise, measuring ranges ±2 to ±2200000 pC, freq. range ≈0 … 200 kHz
Laboratory charge amplifier, multi-channel, low noise, measuring ranges from ±2 to ±2200000 pC